diff --git a/INSTALL b/INSTALL
index 580a583..fbc8300 100644
--- a/INSTALL
+++ b/INSTALL
@@ -148,7 +148,7 @@ for LineageOS to start. Note that if you've used your device before,
 there's no need for this. Also note that the following will wipe your
 userdata on the device:
 
-# mkte2fs -T ext4 /dev/block/mmcblk1p24
+# mke2fs -T ext4 /dev/block/mmcblk1p24
 
 5.2 Optionally reformat mmcblk1p25 emstorage partition as ext4
 
@@ -156,7 +156,7 @@ Based on your needs as described in the PARTITIONS file, optionally
 reformat mmcblk1p25 emstorage partition as ext4. This currently cannot
 be done if using mmcblk1p23 webtop for LineageOS, and mmcblk1p25 emstorage
 must be formatted vfat for that. For LineageOS on mmcblk1p23 webtop
-partition, skip to 5.4.
+partition, skip to 5.3.
 
 $ adb shell
 # mke2fs -T ext4 /dev/block/mmcblk1p25
@@ -165,6 +165,30 @@ There is no need to use any special ext4 flags above as the SafeStrap
 recovery is using the stock v3.0.8 kernel that does not understand the
 newer flags.
 
+note: if you came from LOS14 using Stock partition (mmcblk1p20)
+then you need to reformat mmcblk1p25 to vfat
+
+how to do it, its little bit tricky
+
+first back to firmware folder (VRZ_XT894_9.8.2O-72_VZW-18-8_CFC.xml.zip)
+then flash emstorage to the device, because mke2fs cannot format partition
+to vfat.
+
+type:
+
+host@user# fastboot flash emstorage emstorage.img
+
+now there's a problem, if you see on safestrap recovery,
+the Internal storage free Space is just 25Mb
+
+to get back the rest, you cannot just format using safestrap recovery,
+it will cause the internal a.k.a (/sdcard on safestrap recovery)
+not mount.
+
+to format it. go to Mount menu on safestrap, then Mount USB Storage
+on your host machien you will se new partition 25mb free of 8gb.
+just format it using file manager. to fat32 and it will be back 8gb free.
+
 5.3 Configure mmcblk1p25 emstorage partition active_slot file
 
 The mmcblk1p25 emstorage needs to be configured for LineageOS to use the
@@ -186,6 +210,9 @@ On the device, select "Boot Options" -> "Stock ROM" -> "Activate" if not
 already active. After setting it, red "ROM SLot: stock" should display on
 the top of the screen
 
+for webtop, select "Boot Options" -> "Webtop -> System" -> "Activate"
+then you see on the top left corner ROM Slot: altpart
+
 5.5 Install LineageOS with adb sideload
 
 On the device, select "Advanced" -> "ADB Sideload", check both options
@@ -220,7 +247,10 @@ EOF
 
 Or if booting to mmcblk1p23 webtop altpart:
 
-# cat > /system/boot/boot.cfg << EOF
+$ adb shell
+# mkdir pre
+# mount /dev/block/mmcblk1p23 /pre
+# cat > /pre/boot/boot.cfg << EOF
 LABEL=LineageOS on mmcblk1p23 webtop partition
 PRIORITY=7
 DTB=/etc/kexec/devtree
@@ -239,3 +269,9 @@ you need to do a "factory reset" on the device in SafeStrap under Wipe.
 5.8 Done, reboot the device
 
 The first time LineageOS starts, it will take several minutes to boot.
+
+Note: If you try install LOS14 Using webtop partition,
+	and get black screen after chosee on kexecboot.
+	go to safestrap recovery again check if your webtop partition 
+	(mmmcblk1p23 is ext3 partition type. and the mmcblk1p25 is vfat)
+	you can check by type "blkid"
diff --git a/LOGO b/LOGO
new file mode 100644
index 0000000..d6e2dd1
--- /dev/null
+++ b/LOGO
@@ -0,0 +1,52 @@
+oke here im just want to share about bootlogo/splashscreen
+when the device is booting.
+
+instead of motorola logo im replace it with maemo-leste logo
+
+im suggest it to execute using fastboot from your host machine,
+
+so type this
+
+# fastboot flash logo.bin logo.bin
+# fastboot reboot
+
+and see the different.
+
+if you not gona make your own logo, i have allready logo.bin
+with maemo-leste logo, here:
+#https://github.com/xsetiadi/droid4-kexecboot/blob/master/logo.bin
+
+and if you want to create with another picture
+here the guide
+
+instructions are essentially the same for gimp and photoshop:
+
+create a 540x540 image
+merge into one layer
+
+Gimp: select Colors > Components > Channel Mixer
+
+Photoshop: select Image > Adjustments > Channel Mixer
+
+select Output channel:
+- Red and change the red value from 100 to 0 and the blue value from 0 to 100
+now select Output channel:
+- Blue and change the red value from 0 to 100 and the blue value from 100 to 0
+
+hit OK
+
+Note: the colors will look strange but will display properly on the phone
+
+Gimp: select file > export
+name "logo.bin"
+select "all files" from dropdown menu
+expand the "select file type (by extension)" menu and select "raw image data"
+export
+
+Photoshop: select file > save as
+name "logo.bin"
+format "photoshop raw"
+save
+
+
+Thanks to p3droid and TBH!
diff --git a/logo.bin b/logo.bin
new file mode 100755
index 0000000..ad33770
Binary files /dev/null and b/logo.bin differ