From 5556b071fabf4a53c9dd23da1fa37a21a60aed6a Mon Sep 17 00:00:00 2001 From: scgbckbone Date: Wed, 4 Dec 2024 06:23:43 +0100 Subject: [PATCH] remove help() from stm32 port --- ports/stm32/help.c | 44 +------------------------------------------- 1 file changed, 1 insertion(+), 43 deletions(-) diff --git a/ports/stm32/help.c b/ports/stm32/help.c index fba0a6937fe8a..3b0397660a949 100644 --- a/ports/stm32/help.c +++ b/ports/stm32/help.c @@ -26,46 +26,4 @@ #include "py/builtin.h" -const char stm32_help_text[] = - "Welcome to MicroPython!\n" - "\n" - "For online help please visit http://micropython.org/help/.\n" - "\n" - "Quick overview of commands for the board:\n" - " pyb.info() -- print some general information\n" - " pyb.delay(n) -- wait for n milliseconds\n" - " pyb.millis() -- get number of milliseconds since hard reset\n" - " pyb.Switch() -- create a switch object\n" - " Switch methods: (), callback(f)\n" - " pyb.LED(n) -- create an LED object for LED n (n=1,2,3,4)\n" - " LED methods: on(), off(), toggle(), intensity()\n" - " pyb.Pin(pin) -- get a pin, eg pyb.Pin('X1')\n" - " pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p\n" - " Pin methods: init(..), value([v]), high(), low()\n" - " pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object\n" - " pyb.ADC(pin) -- make an analog object from a pin\n" - " ADC methods: read(), read_timed(buf, freq)\n" - " pyb.DAC(port) -- make a DAC object\n" - " DAC methods: triangle(freq), write(n), write_timed(buf, freq)\n" - " pyb.RTC() -- make an RTC object; methods: datetime([val])\n" - " pyb.rng() -- get a 30-bit hardware random number\n" - " pyb.Servo(n) -- create Servo object for servo n (n=1,2,3,4)\n" - " Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])\n" - " pyb.Accel() -- create an Accelerometer object\n" - " Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()\n" - "\n" - "Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name\n" - "Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD\n" - "Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN\n" - "Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)\n" - "\n" - "Control commands:\n" - " CTRL-A -- on a blank line, enter raw REPL mode\n" - " CTRL-B -- on a blank line, enter normal REPL mode\n" - " CTRL-C -- interrupt a running program\n" - " CTRL-D -- on a blank line, do a soft reset of the board\n" - " CTRL-E -- on a blank line, enter paste mode\n" - "\n" - "For further help on a specific object, type help(obj)\n" - "For a list of available modules, type help('modules')\n" -; +const char stm32_help_text[] = "";